Skip to content

Solar surplus

STABLE COMMUNITY

When your panels produce more than the house consumes, the box uses that surplus on site: it starts and modulates the charging station, the water heater and the other loads it controls, in the order you have set. It redoes this calculation every minute.

What the box calls "surplus"

The box starts from what the main meter measures: the electricity going out to the grid. It adds what the loads it controls are already consuming, so that a running load is not counted against itself. The calculation is always made on the measurement, never on a balance recomputed after control: the box would be reading itself and would oscillate.

With a home battery, what it absorbs counts as surplus when it is above its reserve; its discharge never does. Below the reserve, the battery comes first: no controlled load receives any surplus (see Battery management).

The charging station

The minimum. A charging station does not charge below a minimum current set by the station, usually 6 A (IEC 61851): about 1.4 kW single-phase, 4.1 kW three-phase. Below that it stays stopped and the surplus passes to the next load.

Starting. In Auto mode, the station starts when the sun covers a share of that minimum: the minimum solar coverage, one setting for all stations (see below). At 100 %, it waits until the surplus pays for its whole minimum; at 70 %, a single-phase station starts from about 1 kW of surplus and takes the rest from the grid.

Ramping up and down. Every minute, the current is recalculated on the surplus of the moment, rounded to the ampere, between the station's minimum and maximum and within the limit of each phase of the supply (Load shedding). Two current changes are at least 10 seconds apart.

Stopping and resuming. When the sun no longer covers the required share of the minimum, the station stops and the car stays plugged in; charging resumes when the surplus comes back. To avoid switching the station and the car on and off constantly, the box leaves at least 5 minutes between a start and a stop, and the other way round: a station that has just started stays at its minimum until then, even if the sun disappears for a moment.

Switching between single-phase and three-phase is described on the V2C Trydan page.

Charging modes

The station has two modes, chosen in the app under MODE, on the station's page as on its tile in Favourites: Auto and Manuel (manual; the button keeps this name in every language of the app).

Mode What the box does
Auto Sun first, off-peak hours next. Outside off-peak hours, the station charges on surplus, plus the share of grid power the minimum solar coverage allows. During off-peak hours (peak / off-peak tariff entered), it charges at full power.
Manuel (manual) The Charge switch decides. On: the station charges at full power, at any time, from the grid if needed. Off: the station is stopped, straight away, and receives no more surplus.

Full power, in both modes, means: the station's maximum current, on as many phases as the station and the installation allow, under the limit of each phase of the supply and its margin. The connection protection has the last word.

Switching to Manuel. The app asks "Switch to Manual?" and offers Charge or Charger stopped; Cancel changes nothing. In Manuel, the Charge switch sits next to the mode choice, and the station's page reminds you that it goes back to Auto by itself when unplugged.

Back to Auto. Manuel lasts for one charging session: when the car is unplugged, the station goes back to Auto by itself and the switch returns to off. This also holds when the car left while the box was restarting. The app shows it as soon as the box publishes it.

With a peak / off-peak tariff, Auto mode takes the time of day into account: during off-peak hours, full power, whatever the minimum solar coverage. Manuel does not change with the time of day. Details on the Tariffs page.

Minimum solar coverage

This is the share of the station's minimum that the sun must cover, in Auto mode and outside off-peak hours:

  • 100 %: surplus only. The station starts when the surplus pays for its whole minimum.
  • 0 %: the minimum is always taken from the grid, and the surplus is added on top. The station does not wait for off-peak hours.
  • In between: the station starts when the sun covers that share of its minimum, and buys the rest from the grid. It keeps going while the share is covered, and stops below it. In the 30 minutes after a stop, restarting takes 10 points more: a surplus hovering around the threshold does not switch the station on and off constantly.

During off-peak hours, the coverage has no effect: a station in Auto charges at full power.

One setting for all stations, from 0 to 100 % in steps of 10, in EMS settings → Chargers · Auto mode, in an administrator session. The page of each station in Auto shows the value.

  • New box: 100 %, surplus only.
  • Updated box: the coverage takes over the box's former start setting (the share of the minimum the surplus had to cover): 50 % if it was never changed, the same value otherwise. A setting of zero becomes 100 %: it already meant surplus only.

When the car draws nothing

A station allowed to charge does not make the car charge for sure: battery full, charging scheduled in the car, a car that refuses… When the station is switched on and the car has drawn nothing for two minutes, the line under the station says so, for example: "Charging allowed at 11 kW, but the car draws nothing". The station does not say why: check the car. The box does not change its command, and the line goes away as soon as the car draws again. The app also tells charging allowed apart from charging: a station whose car draws nothing is not shown as charging.

Former modes

The PV, Min+PV modes and those with an end time ("PV + échéance", "Min+PV + échéance") are no longer offered. A station that was in PV is in Auto: it is the same box setting; what changes is full power during off-peak hours.

A station left in another former mode stays in it until someone changes it: the box still serves it, and the app shows "Former setting", without highlighting Auto or Manuel. It never rewrites it by itself.

Former mode What the box does On tapping Auto
Min+PV Surplus first, and the rest bought from the grid up to the station's minimum. With a peak / off-peak tariff: outside off-peak hours, surplus only, the minimum waits for off-peak hours; during off-peak hours, full power. The app opens "The former setting becomes Auto" once and asks for the minimum solar coverage (editable in an administrator session); Cancel changes nothing.
Min+PV + échéance (with end time) The same, and the end time is held. The same.
PV + échéance (with end time) Outside off-peak hours, surplus only; during off-peak hours, full power; the end time is held. Switches to Auto in one tap.

A station left in Manuel since before the update, whose switch was never touched, keeps its former manual settings until it is first unplugged; the app then shows the switch off.

Other loads

  • Relay water heater. It heats in stages (for example 1,000, 2,000, 3,000 W). The box picks the highest stage the surplus pays for; below the first stage, the relay stays open and the surplus passes to the next load. Minimum on and off times prevent flapping.
  • Modulating load (router, dimmer): it receives a continuous setpoint in watts, between its floor and its ceiling.
  • Forcing the heat-up. On the water heater card, Force heating… heats it at full power from the grid for 1 h, 2 h or 4 h, whatever its rank, then solar control resumes. The supply limit still applies during that time.

The order of the loads

All controlled loads are in a single list, set in EMS settings → Controllable loads, by dragging to reorder, in an administrator session. The first is served first: it takes what it needs, within its limits, and the next receives what is left. A load that cannot start with what is left (below its minimum or its first stage) keeps nothing: the surplus passes to the next one. A detected charging station is added at the end of the list; the app points this out.

More details: How the engine decides.

What the app shows

Under each load, a line says why the box made its decision, from the reason it publishes at each cycle: setpoint served by the surplus, no surplus to distribute, budget below the first stage, Manuel at full power, the car draws nothing, waiting for off-peak hours (former modes), phase limit reached… The dashboard groups them in the Right now card.

Going further: the codes

The box publishes a code and its parameters, and the app composes the sentence in your language (NymeaEnergy.GetLoadTelemetry, decision.code). The codes on this page: SURPLUS_SETPOINT, SURPLUS_INSUFFICIENT, BELOW_MIN_POWER, EV_GRID_START (start with a grid top-up), ECO_FLOOR_GRID (minimum from the grid, coverage at 0 %), LOCK_MIN_ON / LOCK_MIN_OFF (minimum on or off time), PHASE_LIMIT, BATTERY_RESERVE, EV_OFF_PEAK_FULL_POWER (Auto during off-peak hours), EV_MANUAL_FULL_POWER (Manuel on), EV_NOT_DRAWING (the car draws nothing), EV_WAITING_OFF_PEAK (former modes), DEROGATION_ACTIVE (forced heating).

Modes (chargingMode, NymeaEnergy.SetChargingInfo): ChargingModeEco (Auto) and ChargingModeNormal (Manuel). The Charge switch is NymeaEnergy.SetEvManualCharging (evChargerId, enabled), which also puts the station in ChargingModeNormal; the return to Auto on unplugging does not happen when lockOnUnplug is set. The former modes, still accepted by the box, are ChargingModeEcoWithMinCurrent (Min+PV), ChargingModeEcoWithTargetTime (PV with end time) and ChargingModeEcoMinWithTargetTime (Min+PV with end time).

The minimum solar coverage is evSolarCoveragePercent (NymeaEnergy.SetEvSolarCoverage, integer from 0 to 100): the same quantity as acquisitionTolerance (0 to 1), times 100; writing either one notifies both. In a station's telemetry, mechanism.chargingEnabled says charging is allowed, mechanism.charging that the car is charging. See the API reference.